It’s Tyre Safety Awareness Month – When did you last have your tyres checked?

#tyresafety #TyreSafe #TyreSafetyMonth

Incorrect tyre pressures can affect: Safety, Fuel Consumption, Tyre Wear, Stopping Distances, Feel & Response and Performance.

In fact, more than a third of us drive with incorrect tyre pressures… When did you last check your pressures?

Contact us for all of your vehicle tyre requirements.

#tyresafety #TyreSafe #TyreSafetyMonth

Depicted as a cross-section of a tyre with an explanation mark, the Tyre Pressure Monitoring System (TPMS) warning light, illuminates when you have a loss in tyre pressure.

You could experience a loss in tyre pressure because of changes in outside temperature OR when you’ve picked up a puncture.

These lights were introduced in reaction to research which showed that a high percentage of motorist travel with incorrect tyre pressures, adversely affecting their fuel consumption and therefore the environment.

When any warning light comes on, you should always get it checked at your earliest convenience. For further help and assistance with your vehicle, Contact Us!

#tyresafety #TyreSafe #TyreSafetyMonth

When were your tyres last checked?

Know your tyre tread depths!

For all of you tyre requirements – contact us!

#tyresafety #TyreSafe #TyreSafetyMonth

It’s Tyre Safety Awareness month and we’ll be bringing you topical tyre related information and knowledge throughout October.

#tyresafety #TyreSafe #TyreSafetyMonth

Changes in season always present a great opportunity to get your vehicle checked over so it’s ready for weather ahead. Book with us for your MOT, Service or Vehicle Health Check this Autumn. Contact us!

Hello Autumn! Is your car ready for the new season ahead?

Fun Fact Friday!

On diesel vehicles, the Glow Plug (or Pre-Heat Plug) warms the combustion chamber to encourage efficient fuel combustion in a diesel engine. The glow plug light naturally illuminates prior to start up and goes out when it’s ready to start the engine. If the glow plug light is on or flashing after the engine is up to temperature it is likely indicating a fault. With the latest diagnostic equipment and expertise, we can assist with all of your vehicle maintenance and diagnostic requirements.

In fact, 80% of replacement glow plug demand occurs between September and March (Source Denso) – Typically when mornings are colder.

Fun Fact Friday!

REMEMBER we can look after your vehicle even if it’s still under manufacturer’s warranty.

We carry out service and maintenance work to the highest standard using quality parts. This means, your warranty is maintained when you bring your vehicle to us!

Wheel Alignment Feature – Part 3:

The Wheel Alignment process is measured in 3 parts: Camber, Caster & Toe

TOE… is the extent to which your tyres turn inwards or outwards, when viewed from above.

Contact us for all of your vehicle maintenance needs!

As we approach a new season, it’s always a good opportunity to check your vehicle is ready for the weather ahead.

If your battery is low on health, often it’ll let you down when the colder weather sets in!

When did you last have your battery tested? Contact us!

SEPTEMBER means new vehicle registrations – look out for those ’73 plates!

REMEMBER: We can look after your vehicle even if it’s still under manufacturer’s warranty. Contact us for all of your vehicle maintenance and repair requirements!

Did you know that a missed or overdue A/C service could cause:

–         Components to fail prematurely

–         Unpleasant smells & bacteria

–         Increased cabin temperature

Book with us & KEEP IT COOL this summer!

Wheel Alignment Feature – Part 2:

The Wheel Alignment process is measured in 3 parts: Camber, Caster & Toe

CASTER… is the angle of the steering axis when viewed from the side.

Contact us for all of your vehicle maintenance needs!

Happy Bank Holiday 🙃

It’s coming up to PEAK MOT TIME –  BOOK EARLY!

REMEMBER: We can carry out your MOT up to 30 days in advance and it’ll still preserve its expiry date!

Wheel Alignment Feature – Part 1:

The Wheel Alignment process is measured in 3 parts: Camber, Caster & Toe

CAMBER… is the angle of the tyre when viewed from the front of the vehicle.

Contact us for all of your vehicle maintenance needs!